skip to Main Content

Packing&Ship-4

Mobile Packing and Shipping

Move your Workplace packing table or shipping station to exactly where you need it—easily, at any time.

Mobile packing tables and shipping workstations from Workplace Modular Systems are available based on either the standard or heavy duty platforms.

Divider specifications are in “Packing Workstation Sizes” accordion section below.

Add-On Accessories for packing and shipping workstationsPacking&Ship-5

A complete range of optional add-on accessories including paper roll holders and divider shelf systems, is available to fine-tune your packing table or shipping station to exact specifications.

Choose from under-table, over-table, computer-related as well as a host of other general accessories.

5" Standard Caster

5″ Standard Caster 

  • Standard caster supplied with all Mobile Workstations unless otherwise specified.
  • “Total Lock” fully lockable caster.
  • Weight Capacity: 250 lbs per caster.

5 Inch Heavy-Duty Caster

5″ Heavy Duty Caster

  • Extra wide wheel design.
  • “Total Lock” fully lockable caster.
  • Weight capacity: 500 lbs per caster.

3 Inch Standard Caster

3″ Standard Caster

  • 3″ diameter side lock caster.
  • Lowers worksurface by 2″ compared to standard 5″ caster.
  • Available for both fixed-height and adjustable height workstations.
  • Weight capacity: 250 lbs per caster.

Standard Leveling Caster

Standard Leveling Caster

  • Hand-or tool-adjustable leveling.
  • Provides low profile clearance (approximately 1/2″) when caster is retracted.
  • Lowers worksurface by 2″ compared to standard 5″ caster.
  • Available for both fixed-height and adjustable height workstations.
  • Working load rating: 550 lbs per caster.

6 Inch Pneumatic Caster

6″ Pneumatic Caster

  • 6″ pneumatic caster allows workstation travel over uneven surfaces.
  • Raises worksurface by 1″ compared to to standard 5″ caster.
  • Stem mounting.
  • Requires reinforced leg extender.

High Clearance Leveling Caster

High Clearance Leveling Caster

  • Tool-adjustable leveling.
  • Requires specialized leg insert to accommodate leveling stem.
  • Provides higher clearance (approximately 1 1/2″) when caster is retracted.
  • Lowers worksurface by 2″ compared to standard 5″ caster.
  • Working load rating: 550 lbs per caster.

5 Inch ESD Caster

5″ ESD Caster

  • “Total Lock” fully lockable caster.
  • Weight Capacity: 250 lbs per caster.
  • Meets Federal Specification FF-C-88C.
  • Requires an average electrical resistance less than 250,000 ohms.

Packing Workstation with Enclosed Panels

To Order, Please Specify Model No. + Color Code + Worksurface Code + Accessories

4800Other Options:

  • ADDITIONAL SIZES (lengths range from 18″ to 96″)
  • Mobile Options
STANDARD SIZES
Model No.DepthLengthHeight
4800-0330”72”36”
4800-0636”72”36”
  • Packing workstation ships assembled (base only)

Packing Workstation with Adjustable Wire Dividers

To Order, Please Specify Model No. + Color Code + Worksurface Code + Accessories

48WD_30Other Options:

  • ADDITIONAL SIZES (lengths range from 18″ to 96″)
  • Mobile option
  • Assembly options

 

STANDARD SIZES
Model No.DepthLengthHeight
4800-1030”60”35”- 42”
4800-1130”72”35”- 42”
4800-1436”72”35”- 42″
  • Workstation ships unassembled

EXP4800

  1. All-metal full-perimeter Frame of 18-gauge furniture-grade steel provides stable support of selected worksurface.
  2. Fully enclosed Panel Leg Sections and full rear enclosure help keep items stored undertable in check.
  3. The Enclosed Panel Workstation is shipped fully assembled, including the fixed all-metal dividers.
  4. Framework at right of Station is designed to allow for addition of optional Drawer Case(s) at any time.

Laminate

PLASTIC LAMINATE TOPS

With Post-Formed Front Edge or Standard Front Edge

The 1-1/16” thick Plastic Laminate Top features an easy-to-clean surface for many general purpose applications. A core of 1” dimensionally stable flakeboard is covered with a plastic laminate surface sheet and edging of .039” thick high-pressure laminate. In addition, a plastic laminate backer sheet of approx. .020” thickness covers the underside of the core stock and ¼-20 metal inserts are located in the underside of the tops for ease of fastening to many of the Workplace frames. The resulting top is a well-balanced, long-lasting work surface.

To specify a standard color Plastic Laminate Top, please use the following codes:

ColorPost-Formed Front

Edge Order Code

Standard Edge

Order Code

Neutral GlacePL-01PFPL-01SQ
Grey GlacePL-02PFPL-02SQ
Frosty WhitePL-03PFPL-03SQ
BlackPL-04PFPL-04SQ
Fashion GreyPL-05PFPL-05SQ
Non-Standard Color*PL-00PFPL-00SQ

*Most Wilsonart International plastic laminate colors are available on special order.
Contact us or call 1-800-258-9700 for assistance.


ESD LAMINATE TOPS
With Post-Formed Front Edge or Standard Front Edge

The ESD Tops feature ESD Laminate, a decorative, clean, amino resin laminate which rapidly dissipates static electrical charges, and is recommended for use in areas which must be free of static electrical charges. The ESD Top is equipped with a flush-mount grounding system (factory-installed) with grounding hardware located on the underside of the Top. A flush-mount grounding bolt is located in the top of the worksurface (at the rear). The flush-mount ground system also includes two banana plugs set flush in the front edge for convenient connection of customer-supplied wrist straps. The ESD Top is fabricated with a dimensionally stable 1” flakeboard used as core stock, with a surface sheet of ESD Laminate covering the top surface and all edges. A plastic laminate backing sheet of at least .020” thickness covers the underside of the top.

Note: ESD Tops require connection to your earth ground system.

To specify an ESD Laminate Top, please use the following codes:

 

ColorPost-Formed Front
Edge Order Code
Standard Edge
Order Code
WhiteES-03PFES-03SQ
Non-Standard Color*ES-00PFES-00SQ

*Additional ESD laminate colors are available. Contact us or call 1-800-258-9700 for assistance.


CHEMICAL RESISTANT LAMINATE TOPS

With Post-Formed Front Edge or Standard Front Edge

The Chemical Resistant Laminate Tops are fabricated in the same manner as the Plastic Laminate Tops. The laminate is a high-pressure decorative laminate recommended for use where accidental spillage of chemical reagents is likely to occur.

To specify a Chemical Resistant Laminate Top, please use the following codes:

ColorPost-Formed Front

Edge Order Code

Standard Edge

Order Code

BlackCR-04PFCR-04SQ
Non-Standard Color*CR-00PFCR-00SQ

*Additional Chemical Resistant Top colors available. Please call 1-800-258-9700 for assistance.

Resin

EPOXY RESIN TOPS

Epoxy Resin Tops are molded from a modified epoxy resin that has been especially compounded and cured to provide optimum physical and chemical resistance required for a heavy duty laboratory working surface. Tops are 1” in thickness with a drip groove provided on the underside of exposed edges; all finished edges have a slight bevel. Sinks and service fixtures are also available upon request.

Note: Silicone adhesive is supplied to mount Top.

To specify an Epoxy Resin Top, please use the following code:

ColorOrder Code
BlackER-01

 

*Additional Epoxy Resin Top colors are available by request. Please call 1-800-258-9700 for assistance.

Note: Add-on Accessories, that suspend from framework (i.e. hanging drawer, keyboard tray, CPU Caddy, etc.) may not be added to workstation after Resin Top is cemented to framework.


PHENOLIC RESIN TOPS

Phenolic Resin Tops provide a homogeneous blend of modified phenolic resins fused together under high pressure and heat in specially designed thermoset press molds to form a solid black chemical resistant composite throughout the entire thickness of the top.

Tops are 1” in thickness with a drip groove provided on the underside of the exposed edges.

Note: Silicone adhesive is supplied to mount Top.

To specify a Phenolic Resin Top, please use the following code:

ColorOrder Code
BlackPR-01

*Additional Phenolic Resin Top colors are available by request. Please call 1-800-258-9700 for assistance.

Wood

MAPLE TOPS

The 1-3/4” thick Maple Tops are constructed of the finest hard maple, fully cured and kiln-dried. The tough butcher-block construction includes placing the laminations on edge and bonding into a single self-supporting solid panel. Front and rear of the maple top top have a ¼” radiused beveled edge.

The Maple Tops may be refinished by sanding. Tops are coated with a Durakryl 102 finish. This rugged acrylic is highly resistant to water, alcohol, detergents, and other solvents.

Note: Please state if end use is to be for food service or preparation.

To specify a Maple Top, please use the following code:

ColorOrder Code
MapleMP-01

Steel

STAINLESS STEEL TOPS

The Stainless Steel Tops are designed as an inverted pan-type top. They are backed with a 1-1/8″ plastic laminate core.  The core is fastened to the table frame with 1/4-20 metal inserts, and the steel pan is then placed directly over the core.  With this method, the usual drumming and noise of a straight metal top is minimized and in some cases, even eliminated.

The standard stainless material is type No. 304 polished finish*.

To specify a Stainless Steel Top, please use the following code:

ColorOrder Code
Stainless Type 304SS-01

 

*Type No. 316, No. 2B finish acid resistant stainless is available by special order. Please call 1-800-258-9700 for assistance.


COLD-ROLLED STEEL TOPS

The Cold-Rolled Steel Tops are designed as an inverted pan top.  They are backed with a 1-1/8″ fiberboard.  The core is fastened to the table frame with 1/4-20 metal inserts; the cold-rolled steel top is then placed directly over the core.

The Cold-Rolled Steel Tops are powder-coated to match the color of the workstation unless specified otherwise.

To specify a Cold-Rolled Steel Top, please use the following code:

ColorOrder Code
Same as workstationCS-01

Workplace Modular Systems metal products feature a highly durable, environmentally friendly powder-coat finish.

STANDARD COLORS

TAN | Color Code: 0001
CHATEAU BLUE| Color Code: 0015
SILVER GRAY (Semi-Metallic) | Color Code: 0002
BLACK WRINKLE (Textured Finish) | Color Code: 0400
MERCURY BLUE | Color Code: 0100
OYSTER | Color Code: 0150
WHITE | Color Code: 0006
NAVY BLUE | Color Code: 0900
BURGUNDY | Color Code: 0950
BLACK (Semi-Gloss) | Color Code: 0018

 

ADDITIONAL COLORS
Many other premium colors are available. Please contact Workplace Modular Systems for additional color selections.

COLOR-MATCHING
Color-matching is also available, subject to additional charge and extended lead time for color-match process.

IMPORTANT!
Actual product color may vary significantly from colors shown above due to color calibration and resolution of viewer monitors. For best color accuracy, please call Workplace at 1-800-258-9700 to request sample metal color chips.

Need Ideas?

It’s easy to transform your work area using hundreds of design ideas found in our idea generator.  This is just a starting point – add or remove components to suit your specific needs.

Idea Generator

contact1

How to Order

It’s the human touch that matters. That’s why you’ll want to connect with one of our Design Specialists Monday through Friday, 8 a.m. to 5 p.m. Eastern Time.

Connect